DB0FS-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0FS-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1781385243	28.6 deg C	38.6 %	1012.8 hPa
1781384343	28.5 deg C	39.1 %	1013 hPa
1781383442	29 deg C	37.9 %	1013 hPa
1781382542	28.8 deg C	38 %	1013.1 hPa
1781381642	28.6 deg C	38.5 %	1013.1 hPa
1781380742	28.9 deg C	36 %	1013.2 hPa
1781379842	28.9 deg C	37.8 %	1013.1 hPa
1781378942	28.7 deg C	38.4 %	1013.2 hPa
1781378042	29.1 deg C	37.3 %	1013 hPa
1781377142	28.9 deg C	37.8 %	1013 hPa
1781376242	28.6 deg C	38.4 %	1013.1 hPa
1781375342	28.9 deg C	37.6 %	1013.1 hPa
1781375010	28.7 deg C	37.9 %	1013.1 hPa
1781374110	28.3 deg C	38.6 %	1013.2 hPa
1781373210	28.7 deg C	37.7 %	1013.1 hPa
1781372310	28.5 deg C	37.8 %	1013.2 hPa
1781371410	29.2 deg C	36.5 %	1013.2 hPa
1781370510	29.1 deg C	36.7 %	1013.1 hPa
1781369610	28.6 deg C	37.6 %	1013 hPa
1781368709	28.5 deg C	37.8 %	1012.9 hPa
1781367809	29.4 deg C	36.4 %	1012.9 hPa
1781366909	29.3 deg C	36.7 %	1012.9 hPa
1781366009	29.2 deg C	37.1 %	1012.9 hPa
1781365109	29 deg C	37.7 %	1013 hPa
1781364209	29.2 deg C	35.5 %	1012.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)