BX6AM-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1765578061	42 C	8 p	48 p	1007 p	22 p
1765576860	42 C	6 p	37 p	986 p	17 p
1765575660	42 C	10 p	39 p	974 p	14 p
1765574486	42 C	5 p	33 p	959 p	10 p
1765573260	42 C	7 p	26 p	949 p	5 p
1765572061	39 C	9 p	22 p	935 p	2 p
1765571616	36 C	0 p	20 p	926 p	1 p
1765571614	35 C	0 p	20 p	926 p	1 p
1765571612	37 C	0 p	20 p	926 p	1 p
1765571609	34 C	0 p	20 p	926 p	1 p
1765569660	43 C	5 p	38 p	922 p	268 p
1765569197	44 C	9 p	43 p	912 p	263 p
1765567260	43 C	7 p	45 p	898 p	258 p
1765566060	43 C	6 p	46 p	884 p	252 p
1765564860	43 C	9 p	44 p	869 p	248 p
1765563661	42 C	9 p	43 p	853 p	245 p
1765562460	42 C	5 p	44 p	838 p	238 p
1765561261	44 C	12 p	45 p	825 p	233 p
1765560060	43 C	8 p	44 p	810 p	229 p
1765558861	43 C	7 p	45 p	794 p	225 p
1765557660	44 C	8 p	45 p	780 p	221 p
1765556460	43 C	9 p	42 p	766 p	217 p
1765555260	44 C	7 p	38 p	749 p	212 p
1765554060	44 C	8 p	35 p	735 p	209 p
1765552861	44 C	7 p	34 p	724 p	206 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)