IW1BPT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IW1BPT-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rete*	Batt1*	Temp*	Hum*
1784717610	230 Volt	13.6 Volt	30 GrdC	41.5 %hum
1784717014	230 Volt	13.6 Volt	30 GrdC	42 %hum
1784716417	230 Volt	13.5 Volt	29.75 GrdC	42.5 %hum
1784715225	230 Volt	13.6 Volt	29.75 GrdC	43.5 %hum
1784714628	230 Volt	13.6 Volt	29.5 GrdC	44 %hum
1784714032	230 Volt	13.6 Volt	29.5 GrdC	44.5 %hum
1784713430	230 Volt	13.6 Volt	29.5 GrdC	45 %hum
1784712834	230 Volt	13.5 Volt	29.25 GrdC	45.5 %hum
1784712238	230 Volt	13.5 Volt	29.25 GrdC	46 %hum
1784711641	230 Volt	13.6 Volt	29 GrdC	46.5 %hum
1784711045	230 Volt	13.5 Volt	28.75 GrdC	47 %hum
1784710449	230 Volt	13.5 Volt	28.75 GrdC	48 %hum
1784709852	230 Volt	13.6 Volt	28.5 GrdC	48.5 %hum
1784709256	230 Volt	13.5 Volt	28.25 GrdC	49 %hum
1784708660	230 Volt	13.5 Volt	28 GrdC	49.5 %hum
1784708063	230 Volt	13.5 Volt	27.75 GrdC	50 %hum
1784707467	230 Volt	13.5 Volt	27.5 GrdC	50.5 %hum
1784706870	230 Volt	13.5 Volt	27 GrdC	51 %hum
1784706274	230 Volt	13.5 Volt	26.75 GrdC	51.5 %hum
1784705678	230 Volt	13.5 Volt	26.5 GrdC	52 %hum
1784705081	230 Volt	13.5 Volt	26 GrdC	52 %hum
1784704485	230 Volt	13.5 Volt	25.75 GrdC	52.5 %hum
1784703889	230 Volt	13.5 Volt	25.5 GrdC	52.5 %hum
1784703292	230 Volt	13.5 Volt	25.25 GrdC	52.5 %hum
1784702696	230 Volt	13.5 Volt	25 GrdC	52.5 %hum

*Used Equation Coefficients:

Rete: 0, 1, 0

Batt1: 0, 0.1, 0

Batt2: 0, 0.1, 0

Temp: 0, 0.25, -20.5

Hum: 0, 0.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)