DL8ZLG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL8ZLG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1775055947	17.6 deg C	48.4 %	1022.8 hPa
1775055047	17 deg C	52.8 %	1023 hPa
1775054147	15.8 deg C	53.9 %	1023.3 hPa
1775053247	17.7 deg C	52.7 %	1023.4 hPa
1775052347	17.5 deg C	55.2 %	1023.7 hPa
1775051447	16.4 deg C	56.6 %	1023.8 hPa
1775050547	15.2 deg C	59.4 %	1024 hPa
1775049646	14.4 deg C	60.4 %	1024.3 hPa
1775048746	15.6 deg C	59.6 %	1024.6 hPa
1775047846	15.3 deg C	60.7 %	1024.8 hPa
1775046946	13.9 deg C	62.4 %	1025 hPa
1775046046	13.9 deg C	63.8 %	1025.1 hPa
1775045146	13.3 deg C	65.1 %	1025.4 hPa
1775044246	12.9 deg C	66.4 %	1025.5 hPa
1775043346	12.4 deg C	67.9 %	1025.5 hPa
1775042446	11.8 deg C	69.4 %	1025.6 hPa
1775041546	11.6 deg C	70.6 %	1025.8 hPa
1775040645	10.4 deg C	70.8 %	1026 hPa
1775039745	10.5 deg C	72.7 %	1026 hPa
1775038845	10 deg C	74.1 %	1026.1 hPa
1775037945	9.8 deg C	74.4 %	1026.1 hPa
1775037045	9.6 deg C	75.8 %	1026.2 hPa
1775036145	9 deg C	76.3 %	1026.2 hPa
1775035245	8.2 deg C	77.2 %	1026.2 hPa
1775034345	8 deg C	77.9 %	1026.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)