DB0HAS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0HAS-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Effic*
1784692400	14.54 Volt	24 °C	700 Pkt
1784692100	14.46 Volt	24 °C	700 Pkt
1784691800	14.54 Volt	24 °C	700 Pkt
1784691499	14.38 Volt	24 °C	700 Pkt
1784691199	14.54 Volt	24 °C	700 Pkt
1784690899	14.3 Volt	24 °C	700 Pkt
1784690598	14.54 Volt	24 °C	700 Pkt
1784690298	14.46 Volt	24 °C	700 Pkt
1784689999	14.54 Volt	24 °C	700 Pkt
1784689998	14.54 Volt	24 °C	700 Pkt
1784689698	14.54 Volt	24 °C	700 Pkt
1784689397	14.54 Volt	24 °C	700 Pkt
1784689097	14.3 Volt	24 °C	700 Pkt
1784688797	14.54 Volt	24 °C	700 Pkt
1784688496	14.38 Volt	24 °C	700 Pkt
1784688196	14.54 Volt	24 °C	700 Pkt
1784687896	14.46 Volt	24 °C	700 Pkt
1784687596	14.54 Volt	24 °C	700 Pkt
1784687295	14.54 Volt	24 °C	700 Pkt
1784686995	14.54 Volt	24 °C	700 Pkt
1784686394	14.54 Volt	24.5 °C	700 Pkt
1784686094	14.54 Volt	24 °C	700 Pkt
1784685794	14.54 Volt	24.5 °C	700 Pkt
1784685494	14.54 Volt	24.5 °C	700 Pkt
1784685193	14.54 Volt	24.5 °C	700 Pkt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Temp: 0, 0.5, -63

Dig1h: 0, 10, 0

RX 1h: 0, 10, 0

Effic: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)