KK7LLM-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK7LLM-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*	Value3*
1789933664	14.18 Volts	108.81 Deg.F	255
1789933634	13.98 Volts	107.93 Deg.F	238
1789933480	14.15 Volts	106.17 Deg.F	245
1789876328	13.65 Volts	64.81 Deg.F	642
1789876180	13.71 Volts	63.93 Deg.F	287
1789876158	13.71 Volts	63.05 Deg.F	638
1789871976	14.03 Volts	74.49 Deg.F	279
1789871956	14.21 Volts	74.49 Deg.F	283
1789871832	13.98 Volts	73.61 Deg.F	286
1789871694	14.03 Volts	71.85 Deg.F	283
1789871653	13.92 Volts	70.97 Deg.F	290
1789871499	13.74 Volts	69.21 Deg.F	636
1789870077	14.21 Volts	75.37 Deg.F	278
1789869962	14.12 Volts	73.61 Deg.F	280
1789869820	13.92 Volts	71.85 Deg.F	290
1789869718	13.98 Volts	70.09 Deg.F	293
1789869697	13.74 Volts	70.09 Deg.F	274
1789858661	13.77 Volts	94.73 Deg.F	263
1789858539	13.42 Volts	95.61 Deg.F	250
1789858388	13.1 Volts	95.61 Deg.F	255
1789858204	13.21 Volts	96.49 Deg.F	245
1789858022	13.19 Volts	97.37 Deg.F	257
1789857840	13.21 Volts	97.37 Deg.F	245
1789850148	12.83 Volts	97.37 Deg.F	513
1789845985	13.6 Volts	94.73 Deg.F	260

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.88, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)