DD9FH-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DD9FH-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp.in*	Hum*	Temp.out*
1787592499	21.1 C deg	46 %	0 C deg
1787590693	21 C deg	45 %	0 C deg
1787590674	21 C deg	45 %	0 C deg
1787588821	21 C deg	46 %	0 C deg
1787587068	20.9 C deg	47 %	0 C deg
1787587015	20.9 C deg	47 %	0 C deg
1787383864	21.4 C deg	54 %	0 C deg
1787382097	21.4 C deg	54 %	0 C deg
1787380221	21.3 C deg	54 %	0 C deg
1787378400	21.3 C deg	54 %	0 C deg
1787378374	21.3 C deg	54 %	0 C deg
1787376543	21.2 C deg	54 %	0 C deg
1787374739	21.2 C deg	54 %	0 C deg
1787332353	22.5 C deg	51 %	0 C deg
1787332330	22.5 C deg	51 %	0 C deg
1787330583	22.4 C deg	52 %	0 C deg
1787330583	22.4 C deg	52 %	0 C deg
1787330513	22.4 C deg	52 %	0 C deg
1787328700	22.4 C deg	52 %	0 C deg
1787326927	22.3 C deg	52 %	0 C deg
1787326923	22.3 C deg	52 %	0 C deg
1787323349	22.1 C deg	51 %	0 C deg
1787321539	22.2 C deg	51 %	0 C deg
1787321520	22.2 C deg	51 %	0 C deg
1787319719	22 C deg	52 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)