SR9BBC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9BBC-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1789968965	1 Count	69 Count	4.12 VDC
1789968064	34 Count	1045 Count	4.11 VDC
1789967195	31 Count	950 Count	4.1 VDC
1789966262	29 Count	886 Count	4.11 VDC
1789965361	27 Count	809 Count	4.09 VDC
1789964460	26 Count	741 Count	4.12 VDC
1789963559	22 Count	661 Count	4.1 VDC
1789962658	20 Count	586 Count	4.11 VDC
1789961757	17 Count	514 Count	4.12 VDC
1789960856	15 Count	440 Count	4.12 VDC
1789959956	12 Count	371 Count	4.12 VDC
1789959054	10 Count	297 Count	4.1 VDC
1789958153	7 Count	221 Count	4.12 VDC
1789957258	4 Count	139 Count	4.1 VDC
1789956351	1 Count	70 Count	4.1 VDC
1789955451	43 Count	1072 Count	4.1 VDC
1789954549	39 Count	996 Count	4.1 VDC
1789953648	37 Count	922 Count	4.11 VDC
1789952747	34 Count	853 Count	4.09 VDC
1789951846	32 Count	787 Count	4.12 VDC
1789950946	29 Count	716 Count	4.11 VDC
1789950045	26 Count	646 Count	4.13 VDC
1789949144	23 Count	576 Count	4.09 VDC
1789948243	19 Count	500 Count	4.11 VDC
1789947342	16 Count	420 Count	4.1 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)