APRS Track Direct

My position About ☰

reset

SQ9PQL-00 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9PQL-00. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1749913160	169 Count	174 Count	89 Count
1749912257	166 Count	170 Count	87 Count
1749911353	163 Count	166 Count	85 Count
1749910449	160 Count	163 Count	83 Count
1749909546	157 Count	160 Count	81 Count
1749908642	154 Count	158 Count	79 Count
1749907738	151 Count	156 Count	77 Count
1749906834	148 Count	153 Count	75 Count
1749905931	145 Count	150 Count	73 Count
1749905027	142 Count	145 Count	71 Count
1749904140	139 Count	140 Count	69 Count
1749903219	136 Count	136 Count	67 Count
1749902316	133 Count	133 Count	65 Count
1749901412	130 Count	128 Count	63 Count
1749900508	127 Count	125 Count	61 Count
1749899605	124 Count	121 Count	59 Count
1749898701	121 Count	116 Count	57 Count
1749897797	118 Count	113 Count	55 Count
1749896983	115 Count	108 Count	53 Count
1749896080	112 Count	105 Count	51 Count
1749895176	109 Count	99 Count	49 Count
1749894272	106 Count	96 Count	47 Count
1749892465	100 Count	88 Count	43 Count
1749890698	94 Count	82 Count	39 Count
1749888850	88 Count	76 Count	35 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: