DH8WM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DH8WM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Humi*	Baro*
1776896007	18.8 deg C	39.1 %	1026.4 hPa
1776895107	18.9 deg C	39.2 %	1026.7 hPa
1776894207	19 deg C	39.1 %	1026.1 hPa
1776893307	19.1 deg C	39.1 %	1026.9 hPa
1776892407	19.1 deg C	39.2 %	1026.3 hPa
1776892075	19.1 deg C	39.1 %	1025.3 hPa
1776891175	19.2 deg C	39.1 %	1028.3 hPa
1776890275	19.1 deg C	39.3 %	1027.2 hPa
1776889375	18.9 deg C	39.5 %	1026.9 hPa
1776888475	19 deg C	39.5 %	1026.5 hPa
1776887575	19 deg C	39.5 %	1025.9 hPa
1776886675	19.1 deg C	39.6 %	1026.8 hPa
1776885775	19.1 deg C	39.6 %	1025.4 hPa
1776884875	19.2 deg C	39.6 %	1027.4 hPa
1776883975	19.2 deg C	39.6 %	1027.1 hPa
1776883075	19.2 deg C	39.6 %	1025.8 hPa
1776882175	19.3 deg C	39.6 %	1026.5 hPa
1776881275	19.4 deg C	39.4 %	1024.9 hPa
1776880374	19.4 deg C	39.4 %	1025.3 hPa
1776880135	19.4 deg C	39.4 %	1025.3 hPa
1776879235	19.4 deg C	39.3 %	1025.7 hPa
1776878335	19.4 deg C	39.2 %	1025.3 hPa
1776877435	19.5 deg C	39.2 %	1024.8 hPa
1776877104	19.4 deg C	39.2 %	1025.7 hPa
1776876204	19.4 deg C	39.2 %	1024.5 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)