KJ5IK-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KJ5IK-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1765698581	14.03 Volt	100 Pcnt	16.5 F
1765697681	14.03 Volt	100 Pcnt	16.5 F
1765696781	14.03 Volt	100 Pcnt	16 F
1765695881	14.03 Volt	100 Pcnt	15.5 F
1765694981	14.03 Volt	100 Pcnt	15.5 F
1765694081	14.03 Volt	100 Pcnt	15.5 F
1765693181	14.03 Volt	100 Pcnt	15 F
1765692281	14.03 Volt	100 Pcnt	15 F
1765691381	14.03 Volt	100 Pcnt	15 F
1765690481	14.03 Volt	100 Pcnt	15.5 F
1765689581	14.03 Volt	100 Pcnt	16 F
1765688682	14.03 Volt	100 Pcnt	16 F
1765687782	14.03 Volt	100 Pcnt	17 F
1765686882	14.03 Volt	100 Pcnt	16.5 F
1765685982	14.03 Volt	100 Pcnt	16 F
1765685082	14.03 Volt	100 Pcnt	16.5 F
1765684182	14.03 Volt	100 Pcnt	16.5 F
1765683282	14.03 Volt	100 Pcnt	17 F
1765682382	14.03 Volt	100 Pcnt	17.5 F
1765681482	14.03 Volt	100 Pcnt	18 F
1765680586	14.03 Volt	100 Pcnt	19 F
1765679682	14.03 Volt	100 Pcnt	19 F
1765678782	14.03 Volt	100 Pcnt	19 F
1765677882	14.03 Volt	100 Pcnt	19 F
1765676982	14.03 Volt	100 Pcnt	19 F

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)