BM2OPC-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM2OPC-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1789968059	48.3 C	35 p	85 p	1658 p
1789966859	47.1 C	11 p	73 p	1640 p
1789965660	47.2 C	39 p	77 p	1644 p
1789964460	47.1 C	23 p	60 p	1618 p
1789963260	46.9 C	15 p	62 p	1602 p
1789962060	46.8 C	22 p	64 p	1598 p
1789960859	47.4 C	25 p	66 p	1596 p
1789959659	47 C	17 p	67 p	1587 p
1789958460	47 C	24 p	108 p	1587 p
1789957260	47.4 C	26 p	118 p	1587 p
1789956060	47.5 C	58 p	120 p	1577 p
1789954860	47.7 C	34 p	89 p	1541 p
1789953659	46.6 C	28 p	83 p	1529 p
1789952460	46.9 C	27 p	82 p	1522 p
1789951259	46.4 C	28 p	90 p	1515 p
1789950059	46.3 C	27 p	104 p	1509 p
1789948859	46.2 C	35 p	123 p	1497 p
1789947659	46 C	42 p	122 p	1483 p
1789946460	46.4 C	46 p	112 p	1467 p
1789945260	45.5 C	34 p	94 p	1443 p
1789944092	45.2 C	32 p	90 p	1430 p
1789942859	46.4 C	28 p	91 p	1420 p
1789941660	47.1 C	30 p	90 p	1401 p
1789940460	45.9 C	33 p	84 p	1386 p
1789939259	45.5 C	27 p	69 p	1371 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)