OE8NDR-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8NDR-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1772707622	12.6 Volt	20 Pkt	10 Pkt	54 Pcnt
1772707322	12.6 Volt	20 Pkt	10 Pkt	56 Pcnt
1772707022	12.6 Volt	20 Pkt	10 Pkt	56 Pcnt
1772706722	12.6 Volt	20 Pkt	0 Pkt	54 Pcnt
1772706422	12.6 Volt	20 Pkt	0 Pkt	54 Pcnt
1772706122	12.6 Volt	20 Pkt	0 Pkt	56 Pcnt
1772705822	12.6 Volt	20 Pkt	0 Pkt	54 Pcnt
1772705522	12.6 Volt	20 Pkt	0 Pkt	58 Pcnt
1772705222	12.6 Volt	20 Pkt	0 Pkt	61 Pcnt
1772704922	12.6 Volt	10 Pkt	0 Pkt	62 Pcnt
1772704622	12.6 Volt	0 Pkt	0 Pkt	40 Pcnt
1772704322	12.6 Volt	0 Pkt	0 Pkt	33 Pcnt
1772704022	12.6 Volt	0 Pkt	0 Pkt	28 Pcnt
1772703722	12.6 Volt	0 Pkt	0 Pkt	21 Pcnt
1772703422	12.6 Volt	0 Pkt	0 Pkt	14 Pcnt
1772703122	12.6 Volt	0 Pkt	0 Pkt	7 Pcnt
1772702822	12.6 Volt	0 Pkt	0 Pkt	8 Pcnt
1772702522	12.6 Volt	0 Pkt	0 Pkt	8 Pcnt
1772702222	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772701922	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772701622	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772701322	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772701022	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772700722	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt
1772700422	12.6 Volt	0 Pkt	0 Pkt	0 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)