SK6LK-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SK6LK-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1772661414	12.3 Volt	7 Pcnt	15 C
1772660514	12.3 Volt	8 Pcnt	15.5 C
1772659614	12.3 Volt	11 Pcnt	15.5 C
1772658714	12.3 Volt	14 Pcnt	16 C
1772657814	12.3 Volt	33 Pcnt	16 C
1772656914	12.3 Volt	100 Pcnt	17 C
1772656014	12.3 Volt	100 Pcnt	17 C
1772655114	12.3 Volt	100 Pcnt	17.5 C
1772654214	12.3 Volt	100 Pcnt	17 C
1772653314	12.3 Volt	100 Pcnt	17 C
1772652414	12.3 Volt	100 Pcnt	17 C
1772651515	12.3 Volt	100 Pcnt	16.5 C
1772650614	12.3 Volt	100 Pcnt	16.5 C
1772649715	12.3 Volt	100 Pcnt	15.5 C
1772648815	12.3 Volt	100 Pcnt	15 C
1772647915	12.3 Volt	75 Pcnt	15.5 C
1772647015	12.3 Volt	25 Pcnt	15 C
1772646123	12.3 Volt	21 Pcnt	14.5 C
1772645215	12.3 Volt	13 Pcnt	13.5 C
1772644315	12.3 Volt	10 Pcnt	13.5 C
1772643415	12.3 Volt	13 Pcnt	13.5 C
1772641615	12.3 Volt	10 Pcnt	13.5 C
1772640715	12.3 Volt	10 Pcnt	14 C
1772639815	12.3 Volt	8 Pcnt	14 C
1772638915	12.3 Volt	8 Pcnt	14 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)