YC2NFD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC2NFD-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1755726941	44 Pkt	31 dBm	13.49 V
1755726210	33 Pkt	31 dBm	13.49 V
1755725392	39 Pkt	31 dBm	13.49 V
1755724661	39 Pkt	31 dBm	13.49 V
1755723930	40 Pkt	31 dBm	13.49 V
1755723198	39 Pkt	31 dBm	13.54 V
1755722380	37 Pkt	31 dBm	13.49 V
1755721653	42 Pkt	31 dBm	13.49 V
1755720920	32 Pkt	31 dBm	13.49 V
1755720192	43 Pkt	31 dBm	13.49 V
1755719373	38 Pkt	31 dBm	13.49 V
1755717912	39 Pkt	31 dBm	13.49 V
1755717183	39 Pkt	31 dBm	13.54 V
1755716365	37 Pkt	31 dBm	13.49 V
1755715635	40 Pkt	31 dBm	13.49 V
1755714903	42 Pkt	31 dBm	13.49 V
1755714171	42 Pkt	31 dBm	13.49 V
1755713278	40 Pkt	31 dBm	13.54 V
1755711815	34 Pkt	31 dBm	13.49 V
1755711086	29 Pkt	31 dBm	13.49 V
1755710368	30 Pkt	-57 dBm	13.49 V
1755709742	21 Pkt	-57 dBm	13.49 V
1755709117	30 Pkt	-57 dBm	13.49 V
1755708493	23 Pkt	-57 dBm	13.49 V
1755707864	30 Pkt	-57 dBm	13.49 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)