F1ZSG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1ZSG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	PA Temp*	Value2*	Value3*	Value4*	Value5*
1784688244	32.87 deg.C	0	0	0	0
1784687643	33.19 deg.C	0	0	0	0
1784686444	33.35 deg.C	0	0	0	0
1784685843	33.51 deg.C	0	0	0	0
1784684344	33.19 deg.C	0	0	0	0
1784684045	33.19 deg.C	0	0	0	0
1784683744	33.19 deg.C	0	0	0	0
1784683445	33.19 deg.C	0	0	0	0
1784683146	33.19 deg.C	0	0	0	0
1784682843	33.19 deg.C	0	0	0	0
1784681944	33.19 deg.C	0	0	0	0
1784681643	33.19 deg.C	0	0	0	0
1784681343	33.19 deg.C	0	0	0	0
1784681045	33.19 deg.C	0	0	0	0
1784680143	33.19 deg.C	0	0	0	0
1784678944	33.51 deg.C	0	0	0	0
1784677444	33.51 deg.C	0	0	0	0
1784677144	33.51 deg.C	0	0	0	0
1784676845	33.51 deg.C	0	0	0	0
1784676544	33.51 deg.C	0	0	0	0
1784675944	33.51 deg.C	0	0	0	0
1784675644	33.67 deg.C	0	0	0	0
1784675343	33.67 deg.C	0	0	0	0
1784674444	33.67 deg.C	0	0	0	0
1784670545	34.31 deg.C	0	0	0	0

*Used Equation Coefficients:

PA Temp: 0, 0.16016, -40

Value2: 0, 0, 0

Value3: 0, 0, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)