CR7BQX-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CR7BQX-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Bat*
1765539023	43 Count	21 Count	15 Count	4.33 VDC
1765537223	42 Count	21 Count	15 Count	4.32 VDC
1765535422	41 Count	21 Count	15 Count	4.31 VDC
1765533621	40 Count	21 Count	15 Count	4.29 VDC
1765530020	38 Count	21 Count	15 Count	4.32 VDC
1765528219	37 Count	21 Count	15 Count	4.31 VDC
1765526418	36 Count	21 Count	15 Count	4.29 VDC
1765524625	35 Count	21 Count	15 Count	4.33 VDC
1765522824	34 Count	21 Count	15 Count	4.33 VDC
1765521023	33 Count	21 Count	15 Count	4.31 VDC
1765519222	32 Count	21 Count	15 Count	4.33 VDC
1765517421	31 Count	21 Count	15 Count	4.34 VDC
1765515621	30 Count	21 Count	15 Count	4.29 VDC
1765513820	29 Count	21 Count	15 Count	4.31 VDC
1765512019	28 Count	21 Count	15 Count	4.34 VDC
1765510219	27 Count	21 Count	15 Count	4.3 VDC
1765508418	26 Count	21 Count	15 Count	4.33 VDC
1765506617	25 Count	21 Count	15 Count	4.34 VDC
1765504816	24 Count	21 Count	15 Count	4.33 VDC
1765503023	23 Count	21 Count	15 Count	4.29 VDC
1765501222	22 Count	21 Count	15 Count	4.34 VDC
1765499422	21 Count	21 Count	15 Count	4.3 VDC
1765497621	20 Count	20 Count	15 Count	4.33 VDC
1765495820	17 Count	17 Count	13 Count	4.34 VDC
1765494019	14 Count	14 Count	11 Count	4.28 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)