AI5TX-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI5TX-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773300220	13.5 Volt	30 Pkt	26 Pcnt
1773296620	13.5 Volt	50 Pkt	37 Pcnt
1773293020	13.5 Volt	40 Pkt	33 Pcnt
1773289423	13.5 Volt	40 Pkt	32 Pcnt
1773285820	13.5 Volt	30 Pkt	26 Pcnt
1773282220	13.5 Volt	10 Pkt	15 Pcnt
1773278620	13.5 Volt	10 Pkt	16 Pcnt
1773275020	13.5 Volt	10 Pkt	19 Pcnt
1773271421	13.5 Volt	10 Pkt	15 Pcnt
1773267821	13.5 Volt	10 Pkt	12 Pcnt
1773264221	13.5 Volt	10 Pkt	15 Pcnt
1773260621	13.5 Volt	10 Pkt	15 Pcnt
1773257021	13.5 Volt	10 Pkt	12 Pcnt
1773253421	13.5 Volt	10 Pkt	15 Pcnt
1773249821	13.5 Volt	10 Pkt	13 Pcnt
1773246221	13.5 Volt	10 Pkt	12 Pcnt
1773242621	13.5 Volt	20 Pkt	15 Pcnt
1773239021	13.5 Volt	40 Pkt	31 Pcnt
1773235421	13.5 Volt	40 Pkt	36 Pcnt
1773224621	13.5 Volt	60 Pkt	53 Pcnt
1773221022	13.5 Volt	40 Pkt	48 Pcnt
1773217422	13.5 Volt	60 Pkt	63 Pcnt
1773213822	13.5 Volt	40 Pkt	60 Pcnt
1773210222	13.5 Volt	30 Pkt	54 Pcnt
1773206622	13.5 Volt	40 Pkt	56 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)