SM7UGO-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SM7UGO-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1761507268	8.1 C deg	76.6 %	0 C deg
1761505468	8.4 C deg	78.1 %	0 C deg
1761456062	8.8 C deg	78.1 %	0 C deg
1761454262	8.8 C deg	77.8 %	0 C deg
1761452474	8.5 C deg	78.5 %	0 C deg
1761450672	8.7 C deg	77.7 %	0 C deg
1761448859	8.9 C deg	77.1 %	0 C deg
1761447059	8.8 C deg	77 %	0 C deg
1761445266	8.9 C deg	76.8 %	0 C deg
1761443458	8.8 C deg	76.8 %	0 C deg
1761438058	8.9 C deg	76.6 %	0 C deg
1761436258	8.8 C deg	76.6 %	0 C deg
1761434458	8.8 C deg	76.7 %	0 C deg
1761430858	8.8 C deg	76.7 %	0 C deg
1761429058	8.8 C deg	76.7 %	0 C deg
1761427258	8.8 C deg	76.4 %	0 C deg
1761425458	8.8 C deg	76.2 %	0 C deg
1761423658	8.8 C deg	75.9 %	0 C deg
1761421858	9 C deg	75.2 %	0 C deg
1761418259	9.6 C deg	74.6 %	0 C deg
1761414657	10.1 C deg	73.8 %	0 C deg
1761411057	10.5 C deg	73.4 %	0 C deg
1761409257	10.7 C deg	73 %	0 C deg
1761407458	11 C deg	72.3 %	0 C deg
1761405657	11.5 C deg	71.3 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)