W1FN-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W1FN-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1753782385	13.13 Volt	370 Pkt	100 Pkt	79 Pcnt
1753778785	13.13 Volt	430 Pkt	110 Pkt	68 Pcnt
1753775185	13.13 Volt	460 Pkt	140 Pkt	77 Pcnt
1753773385	13.2 Volt	510 Pkt	160 Pkt	75 Pcnt
1753771585	13.13 Volt	550 Pkt	160 Pkt	73 Pcnt
1753769785	13.13 Volt	540 Pkt	150 Pkt	78 Pcnt
1753767986	13.2 Volt	510 Pkt	130 Pkt	70 Pcnt
1753766185	13.2 Volt	510 Pkt	120 Pkt	68 Pcnt
1753764385	13.13 Volt	500 Pkt	130 Pkt	76 Pcnt
1753762585	13.13 Volt	510 Pkt	130 Pkt	77 Pcnt
1753760785	13.2 Volt	530 Pkt	130 Pkt	75 Pcnt
1753758985	13.13 Volt	470 Pkt	140 Pkt	71 Pcnt
1753757185	13.2 Volt	410 Pkt	120 Pkt	70 Pcnt
1753755385	13.2 Volt	450 Pkt	120 Pkt	76 Pcnt
1753753585	13.2 Volt	480 Pkt	130 Pkt	74 Pcnt
1753751785	13.2 Volt	470 Pkt	140 Pkt	73 Pcnt
1753749985	13.2 Volt	460 Pkt	140 Pkt	81 Pcnt
1753748185	13.2 Volt	450 Pkt	130 Pkt	82 Pcnt
1753746385	13.2 Volt	450 Pkt	140 Pkt	77 Pcnt
1753744586	13.28 Volt	460 Pkt	140 Pkt	76 Pcnt
1753742786	13.28 Volt	420 Pkt	110 Pkt	76 Pcnt
1753740986	13.28 Volt	400 Pkt	110 Pkt	80 Pcnt
1753739186	13.28 Volt	400 Pkt	120 Pkt	77 Pcnt
1753737386	13.28 Volt	390 Pkt	130 Pkt	74 Pcnt
1753735586	13.28 Volt	390 Pkt	120 Pkt	70 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)