IW2HTZ-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IW2HTZ-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1789975373	46 Count	340 Count	0.28 VDC
1789974465	45 Count	330 Count	0.28 VDC
1789973561	44 Count	325 Count	0.28 VDC
1789972661	43 Count	315 Count	0.28 VDC
1789971753	42 Count	311 Count	0.28 VDC
1789970853	41 Count	304 Count	0.28 VDC
1789969047	39 Count	290 Count	0.28 VDC
1789968142	38 Count	285 Count	0.28 VDC
1789967238	37 Count	276 Count	0.28 VDC
1789966334	36 Count	270 Count	0.28 VDC
1789965426	35 Count	258 Count	0.28 VDC
1789963622	33 Count	242 Count	0.28 VDC
1789962718	32 Count	236 Count	0.28 VDC
1789961810	31 Count	226 Count	0.28 VDC
1789961003	30 Count	220 Count	0.28 VDC
1789960100	29 Count	213 Count	0.28 VDC
1789959196	28 Count	206 Count	0.28 VDC
1789958292	27 Count	196 Count	0.28 VDC
1789957388	26 Count	188 Count	0.28 VDC
1789956484	25 Count	181 Count	0.28 VDC
1789955580	24 Count	175 Count	0.28 VDC
1789954676	22 Count	166 Count	0.28 VDC
1789953772	20 Count	161 Count	0.28 VDC
1789951964	18 Count	149 Count	0.28 VDC
1789951061	17 Count	142 Count	0.28 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)