SA3MHZ-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SA3MHZ-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1765563575	14.8 C	32.26 %	1014.88 hPa
1765559971	18.8 C	31.34 %	1015.25 hPa
1765556367	21 C	35.73 %	1016.38 hPa
1765556309	20.7 C	35.57 %	1018.75 hPa
1765556280	20.4 C	36.06 %	1017 hPa
1765556264	20.4 C	36.06 %	1017.75 hPa
1765556248	20.4 C	36.06 %	1017.25 hPa
1765556230	20.2 C	36.87 %	1018.25 hPa
1765556214	20.2 C	36.87 %	1017 hPa
1765555759	18.1 C	37.96 %	1015.75 hPa
1765555735	17.8 C	38.17 %	1016.13 hPa
1765555717	17.8 C	38.17 %	1016 hPa
1765555602	17.2 C	38.72 %	1016.38 hPa
1765555586	17.2 C	38.72 %	1015.88 hPa
1765555570	17.2 C	38.72 %	1015.88 hPa
1765549860	10 C	47.75 %	1017.13 hPa
1765549818	9.5 C	47.96 %	1011.25 hPa
1765549802	9.5 C	47.96 %	1011.5 hPa
1765549758	9.5 C	47.96 %	1015.25 hPa
1765549742	9.1 C	48.09 %	1015.88 hPa
1765549726	9.1 C	48.09 %	1016.25 hPa
1765549694	8.6 C	48.27 %	1018.88 hPa
1765549678	8.6 C	48.27 %	1018.38 hPa
1765549629	8.1 C	48.3 %	1013.38 hPa
1765549610	8.1 C	48.3 %	1014.13 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)