OK1WJW-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1WJW-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1761503367	12.53 Volt	0 Pkt	0 Pcnt
1761502767	12.53 Volt	0 Pkt	0 Pcnt
1761502167	12.53 Volt	0 Pkt	0 Pcnt
1761501567	12.53 Volt	0 Pkt	0 Pcnt
1761500967	12.53 Volt	0 Pkt	0 Pcnt
1761500367	12.53 Volt	0 Pkt	0 Pcnt
1761499767	12.53 Volt	0 Pkt	0 Pcnt
1761499167	12.53 Volt	0 Pkt	0 Pcnt
1761498567	12.53 Volt	0 Pkt	2 Pcnt
1761497967	12.53 Volt	0 Pkt	2 Pcnt
1761497367	12.53 Volt	0 Pkt	2 Pcnt
1761496767	12.53 Volt	0 Pkt	1 Pcnt
1761496167	12.53 Volt	0 Pkt	1 Pcnt
1761495567	12.53 Volt	0 Pkt	1 Pcnt
1761494967	12.53 Volt	0 Pkt	3 Pcnt
1761494367	12.53 Volt	0 Pkt	3 Pcnt
1761493767	12.53 Volt	0 Pkt	4 Pcnt
1761493167	12.53 Volt	0 Pkt	5 Pcnt
1761492567	12.53 Volt	10 Pkt	8 Pcnt
1761491967	12.53 Volt	10 Pkt	9 Pcnt
1761491367	12.53 Volt	0 Pkt	7 Pcnt
1761490767	12.53 Volt	0 Pkt	6 Pcnt
1761489567	12.53 Volt	0 Pkt	2 Pcnt
1761488967	12.53 Volt	0 Pkt	1 Pcnt
1761488367	12.53 Volt	0 Pkt	1 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)