CX1AA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CX1AA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784776693	9.23 Volt	20 Pkt	71 Pcnt
1784776393	9.23 Volt	10 Pkt	73 Pcnt
1784776344	9.23 Volt	10 Pkt	76 Pcnt
1784776093	9.23 Volt	10 Pkt	76 Pcnt
1784775793	9.23 Volt	10 Pkt	73 Pcnt
1784775493	9.23 Volt	10 Pkt	76 Pcnt
1784775253	9.23 Volt	20 Pkt	78 Pcnt
1784775193	9.23 Volt	20 Pkt	78 Pcnt
1784774893	9.23 Volt	20 Pkt	76 Pcnt
1784774593	9.23 Volt	20 Pkt	80 Pcnt
1784774317	9.23 Volt	20 Pkt	86 Pcnt
1784774293	9.23 Volt	20 Pkt	86 Pcnt
1784773993	9.23 Volt	20 Pkt	84 Pcnt
1784773693	9.23 Volt	20 Pkt	84 Pcnt
1784773524	9.23 Volt	20 Pkt	84 Pcnt
1784773393	9.23 Volt	20 Pkt	84 Pcnt
1784773093	9.23 Volt	20 Pkt	84 Pcnt
1784772793	9.23 Volt	20 Pkt	83 Pcnt
1784772518	9.23 Volt	20 Pkt	85 Pcnt
1784772493	9.23 Volt	20 Pkt	85 Pcnt
1784771893	9.23 Volt	20 Pkt	88 Pcnt
1784771693	9.23 Volt	20 Pkt	84 Pcnt
1784771593	9.23 Volt	20 Pkt	84 Pcnt
1784771293	9.23 Volt	20 Pkt	86 Pcnt
1784770993	9.23 Volt	20 Pkt	85 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)