VK4RDL-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4RDL-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT*	Rx1h*	Dg1h*	Eff1h*
1789954244	14.22 Volt	150 Pkt	70 Pkt	76 Pcnt
1789953342	14.3 Volt	160 Pkt	70 Pkt	70 Pcnt
1789952441	14.3 Volt	170 Pkt	80 Pkt	61 Pcnt
1789951540	14.22 Volt	170 Pkt	80 Pkt	55 Pcnt
1789950639	14.3 Volt	170 Pkt	80 Pkt	48 Pcnt
1789949738	14.22 Volt	200 Pkt	90 Pkt	46 Pcnt
1789948837	14.22 Volt	230 Pkt	90 Pkt	45 Pcnt
1789947937	13.9 Volt	280 Pkt	110 Pkt	46 Pcnt
1789947035	14.22 Volt	360 Pkt	130 Pkt	51 Pcnt
1789946134	14.69 Volt	390 Pkt	130 Pkt	56 Pcnt
1789945234	13.75 Volt	430 Pkt	130 Pkt	64 Pcnt
1789944334	13.98 Volt	460 Pkt	130 Pkt	70 Pcnt
1789943432	13.83 Volt	460 Pkt	130 Pkt	72 Pcnt
1789942531	13.98 Volt	460 Pkt	130 Pkt	71 Pcnt
1789941630	13.83 Volt	440 Pkt	140 Pkt	71 Pcnt
1789940730	13.75 Volt	430 Pkt	140 Pkt	69 Pcnt
1789939829	13.67 Volt	450 Pkt	130 Pkt	69 Pcnt
1789938929	13.59 Volt	460 Pkt	130 Pkt	70 Pcnt
1789938027	13.35 Volt	490 Pkt	150 Pkt	67 Pcnt
1789937126	13.11 Volt	520 Pkt	150 Pkt	66 Pcnt
1789936226	13.04 Volt	530 Pkt	160 Pkt	65 Pcnt
1789935324	13.04 Volt	540 Pkt	180 Pkt	65 Pcnt
1789934424	13.04 Volt	540 Pkt	180 Pkt	63 Pcnt
1789933522	12.96 Volt	550 Pkt	180 Pkt	65 Pcnt
1789932621	13.04 Volt	530 Pkt	190 Pkt	64 Pcnt

*Used Equation Coefficients:

BATT: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)