AI0ET-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI0ET-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbatt*	VbattTemp*	intTemp*	extTemp*
1773218196	12.48 Volts	46 F	63 F	40 F
1773217596	12.51 Volts	47 F	63 F	40 F
1773216996	12.51 Volts	47 F	63 F	40 F
1773216396	12.51 Volts	47 F	63 F	40 F
1773215796	12.54 Volts	47 F	64 F	41 F
1773215196	12.51 Volts	47 F	64 F	41 F
1773214596	12.54 Volts	48 F	64 F	41 F
1773213996	12.54 Volts	48 F	64 F	41 F
1773213396	12.55 Volts	48 F	64 F	41 F
1773212796	12.58 Volts	48 F	65 F	42 F
1773212196	12.58 Volts	48 F	65 F	42 F
1773211596	12.58 Volts	48 F	65 F	42 F
1773210995	12.6 Volts	48 F	65 F	42 F
1773210396	12.59 Volts	48 F	65 F	42 F
1773209796	12.62 Volts	48 F	65 F	43 F
1773209196	12.61 Volts	48 F	65 F	43 F
1773208595	12.64 Volts	48 F	66 F	43 F
1773207996	12.65 Volts	48 F	66 F	43 F
1773207396	12.65 Volts	48 F	66 F	43 F
1773206795	12.66 Volts	49 F	66 F	43 F
1773206196	12.69 Volts	49 F	67 F	44 F
1773205596	12.66 Volts	49 F	67 F	44 F
1773204995	12.66 Volts	49 F	67 F	44 F
1773204396	12.71 Volts	49 F	67 F	44 F
1773203796	12.71 Volts	49 F	67 F	45 F

*Used Equation Coefficients:

Vbatt: 0, 0.01, 0

Vsolar: 0, 0.01, 0

VbattTemp: 0, 1, 0

intTemp: 0, 1, 0

extTemp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)