SR9WXS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXS. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	HostTx10m*
1772636721	119 Pkt	21 Pkt	19 Pkt	0 Pkt
1772636117	98 Pkt	18 Pkt	17 Pkt	1 Pkt
1772635517	97 Pkt	21 Pkt	18 Pkt	0 Pkt
1772634917	99 Pkt	13 Pkt	11 Pkt	0 Pkt
1772634212	94 Pkt	19 Pkt	17 Pkt	0 Pkt
1772633613	105 Pkt	15 Pkt	14 Pkt	0 Pkt
1772633011	117 Pkt	10 Pkt	8 Pkt	1 Pkt
1772632407	119 Pkt	18 Pkt	17 Pkt	0 Pkt
1772631808	90 Pkt	4 Pkt	3 Pkt	1 Pkt
1772631208	87 Pkt	9 Pkt	5 Pkt	0 Pkt
1772629543	138 Pkt	26 Pkt	25 Pkt	0 Pkt
1772628939	98 Pkt	9 Pkt	8 Pkt	1 Pkt
1772628339	100 Pkt	13 Pkt	10 Pkt	1 Pkt
1772627739	119 Pkt	15 Pkt	13 Pkt	0 Pkt
1772626014	105 Pkt	13 Pkt	11 Pkt	0 Pkt
1772625411	100 Pkt	14 Pkt	13 Pkt	1 Pkt
1772624811	105 Pkt	10 Pkt	10 Pkt	1 Pkt
1772624211	121 Pkt	22 Pkt	18 Pkt	0 Pkt
1772623267	122 Pkt	20 Pkt	19 Pkt	0 Pkt
1772622666	94 Pkt	17 Pkt	15 Pkt	0 Pkt
1772622062	125 Pkt	18 Pkt	15 Pkt	0 Pkt
1772621462	107 Pkt	24 Pkt	23 Pkt	0 Pkt
1772620862	95 Pkt	20 Pkt	14 Pkt	0 Pkt
1772619798	131 Pkt	9 Pkt	8 Pkt	0 Pkt
1772619197	105 Pkt	10 Pkt	6 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)