VK4RBY-B Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4RBY-B. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tx5m*	CPU-c*	Mem%*
1789981201	0 Count	48 degC	10 Pct
1789979401	0 Count	46 degC	10 Pct
1789977601	0 Count	46 degC	10 Pct
1789975801	0 Count	47 degC	10 Pct
1789974001	0 Count	46 degC	10 Pct
1789972201	0 Count	47 degC	10 Pct
1789970401	0 Count	46 degC	10 Pct
1789968601	0 Count	47 degC	10 Pct
1789966801	0 Count	46 degC	10 Pct
1789965001	0 Count	46 degC	10 Pct
1789963201	0 Count	47 degC	10 Pct
1789961401	0 Count	45 degC	10 Pct
1789959601	0 Count	45 degC	10 Pct
1789957801	1 Count	45 degC	10 Pct
1789956001	0 Count	45 degC	10 Pct
1789954201	0 Count	50 degC	10 Pct
1789952401	0 Count	49 degC	10 Pct
1789950601	0 Count	49 degC	10 Pct
1789948801	0 Count	48 degC	10 Pct
1789947001	0 Count	48 degC	10 Pct
1789945201	0 Count	48 degC	10 Pct
1789943401	0 Count	48 degC	10 Pct
1789941601	0 Count	47 degC	10 Pct
1789939801	0 Count	48 degC	10 Pct
1789938001	0 Count	48 degC	10 Pct

*Used Equation Coefficients:

Tx5m: 0, 1, 0

Rx5m: 0, 1, 0

CPU-c: 0, 1, 20

Mem%: 0, 1, 0

RPTxT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)