BX2AMP-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AMP-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1755663600	38.8 C	14 p	47 p	1987 p
1755662400	39.2 C	14 p	51 p	2015 p
1755661200	38.6 C	19 p	57 p	2022 p
1755659999	37.9 C	18 p	57 p	2018 p
1755658800	38 C	20 p	59 p	2014 p
1755657600	37.4 C	19 p	60 p	2013 p
1755656399	36.3 C	20 p	62 p	2024 p
1755655200	37.4 C	21 p	96 p	2040 p
1755653999	38.5 C	21 p	165 p	2054 p
1755652799	37.7 C	54 p	186 p	2079 p
1755651600	37.1 C	90 p	163 p	2091 p
1755650399	33.2 C	42 p	97 p	2088 p
1755649200	33.1 C	31 p	105 p	2134 p
1755648000	32.7 C	24 p	109 p	2181 p
1755646800	32.7 C	50 p	103 p	2211 p
1755645600	32.3 C	35 p	72 p	2191 p
1755644400	31.6 C	18 p	55 p	2171 p
1755643200	31.5 C	19 p	75 p	2190 p
1755642000	32.1 C	18 p	81 p	2200 p
1755640800	32.6 C	38 p	84 p	2195 p
1755639600	32.9 C	25 p	65 p	2177 p
1755638400	32.8 C	21 p	62 p	2170 p
1755637199	31.7 C	19 p	56 p	2166 p
1755636000	31.7 C	22 p	56 p	2164 p
1755634800	32.1 C	15 p	54 p	2163 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)