This is the latest recevied telemetry packets stored in our database for station/object GW1ATZ-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1761507711
20 Count
0 Count
0 Count
0 VDC
0 VDC
1761505911
19 Count
0 Count
0 Count
0 VDC
0 VDC
1761504116
18 Count
0 Count
0 Count
0 VDC
0 VDC
1761502309
17 Count
0 Count
0 Count
0 VDC
0 VDC
1761500508
16 Count
0 Count
0 Count
0 VDC
0 VDC
1761496907
14 Count
0 Count
0 Count
0 VDC
0 VDC
1761495113
13 Count
0 Count
0 Count
0 VDC
0 VDC
1761493315
12 Count
0 Count
0 Count
0 VDC
0 VDC
1761491511
11 Count
0 Count
0 Count
0 VDC
0 VDC
1761489710
10 Count
0 Count
0 Count
0 VDC
0 VDC
1761487911
9 Count
0 Count
0 Count
0 VDC
0 VDC
1761486109
8 Count
0 Count
0 Count
0 VDC
0 VDC
1761484308
7 Count
0 Count
0 Count
0 VDC
0 VDC
1761482507
6 Count
0 Count
0 Count
0 VDC
0 VDC
1761480707
5 Count
0 Count
0 Count
0 VDC
0 VDC
1761478906
4 Count
0 Count
0 Count
0 VDC
0 VDC
1761475304
2 Count
0 Count
0 Count
0 VDC
0 VDC
1761474374
1 Count
0 Count
0 Count
0 VDC
0 VDC
1761472573
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)