BX2AMP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AMP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1755498615	43.5 C	4 p	9 p	257 p
1755497415	44 C	2 p	9 p	254 p
1755496214	43.2 C	3 p	10 p	255 p
1755495015	43.5 C	4 p	8 p	255 p
1755493815	43.9 C	3 p	8 p	255 p
1755492614	44.7 C	1 p	8 p	255 p
1755491415	43.9 C	4 p	9 p	257 p
1755490215	43.6 C	3 p	12 p	257 p
1755489014	43.6 C	2 p	12 p	257 p
1755487816	42.8 C	7 p	12 p	258 p
1755486615	42.6 C	3 p	9 p	258 p
1755485415	42.3 C	2 p	9 p	255 p
1755484214	42.4 C	4 p	10 p	256 p
1755483015	41.4 C	3 p	9 p	256 p
1755481815	40.8 C	3 p	9 p	256 p
1755480614	40.1 C	3 p	9 p	255 p
1755479415	39.4 C	3 p	10 p	256 p
1755478215	38.9 C	3 p	10 p	256 p
1755477014	38.4 C	4 p	10 p	256 p
1755475814	38 C	3 p	10 p	256 p
1755474615	37.6 C	3 p	11 p	256 p
1755473415	37.4 C	4 p	11 p	257 p
1755472214	37.1 C	4 p	11 p	257 p
1755471015	37.4 C	3 p	10 p	256 p
1755469815	37.3 C	4 p	10 p	256 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)