SP7TPC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP7TPC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX*	RX*	V_Bat*
1784680043	30 Count	38 Count	0 VDC
1784678243	29 Count	36 Count	0 VDC
1784676449	29 Count	34 Count	0 VDC
1784674649	27 Count	32 Count	0 VDC
1784672849	27 Count	30 Count	0 VDC
1784671049	26 Count	28 Count	0 VDC
1784669248	25 Count	26 Count	0 VDC
1784667448	24 Count	25 Count	0 VDC
1784665648	23 Count	23 Count	0 VDC
1784663848	23 Count	21 Count	0 VDC
1784662047	21 Count	19 Count	0 VDC
1784660247	21 Count	17 Count	0 VDC
1784658447	19 Count	15 Count	0 VDC
1784656647	19 Count	13 Count	0 VDC
1784656639	19 Count	12 Count	0 VDC
1784655984	19 Count	12 Count	3.61 VDC
1784654184	17 Count	10 Count	3.6 VDC
1784654158	17 Count	10 Count	3.61 VDC
1784654137	17 Count	10 Count	3.6 VDC
1784653978	17 Count	10 Count	3.6 VDC
1784653975	17 Count	10 Count	3.6 VDC
1784650491	11 Count	6 Count	3.6 VDC
1784650412	10 Count	6 Count	3.6 VDC
1784650380	9 Count	6 Count	3.61 VDC
1784650325	8 Count	5 Count	3.6 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)