This is the latest recevied telemetry packets stored in our database for station/object EA4GMY-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1788504670
399 Count
0 Count
0 Count
0 VDC
0 VDC
1788500155
394 Count
0 Count
0 Count
0 VDC
0 VDC
1788499252
393 Count
0 Count
0 Count
0 VDC
0 VDC
1788497445
391 Count
0 Count
0 Count
0 VDC
0 VDC
1788496567
390 Count
0 Count
0 Count
0 VDC
0 VDC
1788495639
389 Count
0 Count
0 Count
0 VDC
0 VDC
1788494736
388 Count
0 Count
0 Count
0 VDC
0 VDC
1788475842
363 Count
0 Count
0 Count
0 VDC
0 VDC
1788469521
356 Count
0 Count
0 Count
0 VDC
0 VDC
1788450627
331 Count
0 Count
0 Count
0 VDC
0 VDC
1788446183
322 Count
0 Count
0 Count
0 VDC
0 VDC
1788426315
300 Count
0 Count
0 Count
0 VDC
0 VDC
1788425483
295 Count
0 Count
0 Count
0 VDC
0 VDC
1788423677
293 Count
0 Count
0 Count
0 VDC
0 VDC
1788415550
284 Count
0 Count
0 Count
0 VDC
0 VDC
1788365119
220 Count
0 Count
0 Count
0 VDC
0 VDC
1788226539
38 Count
0 Count
0 Count
0 VDC
0 VDC
1787789063
472 Count
2 Count
2 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)