SQ4HSE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ4HSE-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Bat*
1773041035	79 Count	130 Count	24 Count	4.11 VDC
1773039235	77 Count	127 Count	23 Count	4.1 VDC
1773037436	75 Count	123 Count	22 Count	4.11 VDC
1773033834	72 Count	118 Count	21 Count	4.11 VDC
1773032035	70 Count	116 Count	20 Count	4.1 VDC
1773030235	69 Count	114 Count	20 Count	4.11 VDC
1773028435	68 Count	113 Count	20 Count	4.11 VDC
1773026632	67 Count	111 Count	20 Count	4.11 VDC
1773024832	65 Count	109 Count	19 Count	4.11 VDC
1773023031	64 Count	107 Count	19 Count	4.11 VDC
1773021232	63 Count	106 Count	19 Count	4.11 VDC
1773019430	62 Count	104 Count	19 Count	4.11 VDC
1773017629	60 Count	102 Count	18 Count	4.11 VDC
1773015828	59 Count	100 Count	18 Count	4.11 VDC
1773014027	58 Count	99 Count	18 Count	4.11 VDC
1773012227	57 Count	97 Count	18 Count	4.11 VDC
1773010426	55 Count	95 Count	17 Count	4.11 VDC
1773008624	54 Count	93 Count	17 Count	4.1 VDC
1773006826	53 Count	92 Count	17 Count	4.1 VDC
1773005022	52 Count	90 Count	17 Count	4.11 VDC
1773003222	50 Count	88 Count	16 Count	4.11 VDC
1773001421	49 Count	86 Count	16 Count	4.11 VDC
1772999621	48 Count	85 Count	16 Count	4.11 VDC
1772997820	47 Count	83 Count	16 Count	4.11 VDC
1772996021	45 Count	80 Count	15 Count	4.1 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)