This is the latest recevied telemetry packets stored in our database for station/object SA0FRD-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Celsius*
Rel_Hum*
Atm_Press*
Value4*
Value5*
1755546628
25.9 C
58.27 %
1015.88 hPa
0
0
1755537585
26 C
56.76 %
1011.5 hPa
0
0
1755537214
26.4 C
56.04 %
1019.38 hPa
0
0
1755342973
23.8 C
50.28 %
1012.75 hPa
0
0
1755342802
23.6 C
49.99 %
1013 hPa
0
0
1755342140
22.2 C
50.29 %
1012.5 hPa
0
0
1755341853
21.9 C
51.98 %
1015.25 hPa
0
0
1755341570
21.7 C
52.92 %
1013.63 hPa
0
0
1755341167
21 C
53.82 %
1014 hPa
0
0
1755340768
20.6 C
56.79 %
1013.88 hPa
0
0
1755340489
709 C
6125 %
8114 hPa
0
0
1755324293
677 C
6338 %
8120 hPa
0
0
1755324002
677 C
6359 %
8118 hPa
0
0
1755323576
677 C
6364 %
8118 hPa
0
0
1755323162
680 C
6208 %
8108 hPa
0
0
1755322967
681 C
6164 %
8113 hPa
0
0
1755322752
682 C
6069 %
8120 hPa
0
0
1755322574
687 C
5907 %
8117 hPa
0
0
1755291785
755 C
5639 %
8106 hPa
0
0
*Used Equation Coefficients:
Celsius: 0, 0.1, -50
Rel_Hum: 0, 0.01, 0
Atm_Press: 0, 0.125, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)