DK4YU-77 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DK4YU-77. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Press*	Temp.in*	Temp.out*
1788553914	969.1 hPa	29.3 C deg	0 C deg
1788553904	969.1 hPa	29.3 C deg	0 C deg
1788552084	968.7 hPa	29.4 C deg	0 C deg
1788552074	968.7 hPa	29.4 C deg	0 C deg
1788550256	968.7 hPa	29.4 C deg	0 C deg
1788550244	968.7 hPa	29.4 C deg	0 C deg
1788548469	968.3 hPa	29.6 C deg	0 C deg
1788548430	968.3 hPa	29.6 C deg	0 C deg
1788548413	968.3 hPa	29.6 C deg	0 C deg
1788546620	968.2 hPa	29.6 C deg	0 C deg
1788546599	968.2 hPa	29.6 C deg	0 C deg
1788546583	968.2 hPa	29.6 C deg	0 C deg
1788544765	967.8 hPa	29.7 C deg	0 C deg
1788544753	967.8 hPa	29.7 C deg	0 C deg
1788542942	967.5 hPa	29.8 C deg	0 C deg
1788542941	967.5 hPa	29.8 C deg	0 C deg
1788541161	967.4 hPa	29.9 C deg	0 C deg
1788541102	967.4 hPa	29.9 C deg	0 C deg
1788541093	967.4 hPa	29.9 C deg	0 C deg
1788539280	967.5 hPa	29.9 C deg	0 C deg
1788539273	967.5 hPa	29.9 C deg	0 C deg
1788539263	967.5 hPa	29.9 C deg	0 C deg
1788537445	967.8 hPa	30 C deg	0 C deg
1788537433	967.8 hPa	30 C deg	0 C deg
1788535618	968.1 hPa	30.1 C deg	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)