This is the latest recevied telemetry packets stored in our database for station/object GW1ATZ-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1755760152
147 Count
501 Count
103 Count
0 VDC
0 VDC
1755756543
141 Count
473 Count
99 Count
0 VDC
0 VDC
1755752934
137 Count
443 Count
97 Count
0 VDC
0 VDC
1755749326
132 Count
422 Count
94 Count
0 VDC
0 VDC
1755745717
129 Count
407 Count
93 Count
0 VDC
0 VDC
1755742108
123 Count
374 Count
89 Count
0 VDC
0 VDC
1755716949
82 Count
194 Count
62 Count
0 VDC
0 VDC
1755713340
75 Count
170 Count
57 Count
0 VDC
0 VDC
1755709731
61 Count
136 Count
45 Count
0 VDC
0 VDC
1755706122
56 Count
111 Count
42 Count
0 VDC
0 VDC
1755702514
45 Count
89 Count
33 Count
0 VDC
0 VDC
1755698905
35 Count
58 Count
25 Count
0 VDC
0 VDC
1755697103
30 Count
51 Count
21 Count
0 VDC
0 VDC
1755693496
18 Count
31 Count
11 Count
0 VDC
0 VDC
1755689889
5 Count
4 Count
0 Count
0 VDC
0 VDC
1755689834
4 Count
4 Count
0 Count
0 VDC
0 VDC
1755689146
2 Count
2 Count
0 Count
0 VDC
0 VDC
1755688542
1 Count
2 Count
0 Count
0 VDC
0 VDC
1755688320
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)