LA2N-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LA2N-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1789831045	14.33 Volt	0 Pcnt	11 C
1789829843	14.33 Volt	0 Pcnt	11 C
1789829543	14.33 Volt	0 Pcnt	11 C
1789829243	14.33 Volt	4 Pcnt	11 C
1789828943	14.33 Volt	4 Pcnt	11 C
1789828642	14.33 Volt	5 Pcnt	11 C
1789827745	14.33 Volt	4 Pcnt	11 C
1789827141	14.33 Volt	5 Pcnt	11 C
1789825039	14.33 Volt	0 Pcnt	11 C
1789824739	14.33 Volt	0 Pcnt	11 C
1789824438	14.33 Volt	0 Pcnt	11 C
1789822637	14.33 Volt	0 Pcnt	11 C
1789820535	14.33 Volt	0 Pcnt	11 C
1789820234	14.33 Volt	0 Pcnt	11 C
1789819934	14.33 Volt	0 Pcnt	11 C
1789819033	14.33 Volt	0 Pcnt	11 C
1789818733	14.33 Volt	0 Pcnt	11 C
1789818132	14.33 Volt	2 Pcnt	11 C
1789817832	14.33 Volt	2 Pcnt	11 C
1789817532	14.33 Volt	2 Pcnt	11 C
1789817231	14.33 Volt	2 Pcnt	11 C
1789816931	14.33 Volt	2 Pcnt	11 C
1789816631	14.33 Volt	2 Pcnt	11 C
1789816331	14.33 Volt	2 Pcnt	11 C
1789816030	14.33 Volt	2 Pcnt	11 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)