EB7GYR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EB7GYR-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	EfTot*
1784687695	13.35 Volt	100 Pcnt	91 Pcnt
1784687395	13.35 Volt	100 Pcnt	91 Pcnt
1784687095	13.35 Volt	100 Pcnt	91 Pcnt
1784686812	13.35 Volt	100 Pcnt	91 Pcnt
1784686495	13.35 Volt	100 Pcnt	91 Pcnt
1784686195	13.35 Volt	100 Pcnt	91 Pcnt
1784685895	13.35 Volt	100 Pcnt	91 Pcnt
1784685595	13.35 Volt	100 Pcnt	91 Pcnt
1784685295	13.35 Volt	100 Pcnt	91 Pcnt
1784684995	13.35 Volt	100 Pcnt	91 Pcnt
1784684695	13.35 Volt	100 Pcnt	91 Pcnt
1784684395	13.35 Volt	100 Pcnt	91 Pcnt
1784684095	13.35 Volt	100 Pcnt	91 Pcnt
1784683795	13.35 Volt	100 Pcnt	91 Pcnt
1784683495	13.35 Volt	100 Pcnt	91 Pcnt
1784683195	13.35 Volt	100 Pcnt	91 Pcnt
1784682895	13.35 Volt	100 Pcnt	91 Pcnt
1784682595	13.35 Volt	100 Pcnt	91 Pcnt
1784682295	13.35 Volt	100 Pcnt	91 Pcnt
1784681995	13.35 Volt	100 Pcnt	91 Pcnt
1784681695	13.35 Volt	100 Pcnt	91 Pcnt
1784681395	13.35 Volt	100 Pcnt	91 Pcnt
1784681095	13.35 Volt	100 Pcnt	91 Pcnt
1784680795	13.35 Volt	100 Pcnt	91 Pcnt
1784680503	13.35 Volt	100 Pcnt	91 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

EfTot: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)