IS0CAP-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IS0CAP-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Eff1h*
1757255629	12.72 Volt	200 Pkt	93 Pcnt
1757254729	12.72 Volt	220 Pkt	96 Pcnt
1757253829	12.72 Volt	230 Pkt	97 Pcnt
1757252929	12.72 Volt	230 Pkt	97 Pcnt
1757252029	12.72 Volt	230 Pkt	97 Pcnt
1757251129	12.72 Volt	250 Pkt	96 Pcnt
1757250229	12.72 Volt	250 Pkt	97 Pcnt
1757249329	12.72 Volt	250 Pkt	97 Pcnt
1757248429	12.72 Volt	250 Pkt	98 Pcnt
1757246629	12.72 Volt	200 Pkt	97 Pcnt
1757245729	12.72 Volt	200 Pkt	99 Pcnt
1757243029	12.72 Volt	220 Pkt	99 Pcnt
1757241230	12.72 Volt	240 Pkt	97 Pcnt
1757240330	12.72 Volt	230 Pkt	97 Pcnt
1757239430	12.64 Volt	230 Pkt	97 Pcnt
1757238536	12.64 Volt	210 Pkt	97 Pcnt
1757237630	12.64 Volt	180 Pkt	97 Pcnt
1757236730	12.64 Volt	190 Pkt	96 Pcnt
1757235830	12.64 Volt	180 Pkt	96 Pcnt
1757234930	12.64 Volt	190 Pkt	95 Pcnt
1757234030	12.64 Volt	190 Pkt	95 Pcnt
1757233130	12.64 Volt	220 Pkt	95 Pcnt
1757232230	12.64 Volt	210 Pkt	95 Pcnt
1757231330	12.64 Volt	160 Pkt	96 Pcnt
1757230430	12.64 Volt	110 Pkt	95 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)