OE5RGM-20 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE5RGM-20. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Press*	Temp.in*	QNH*	Temp.out*
1777025808	986.1 hPa	22.7 C deg	1026 hPa	16.6 C deg
1777018548	986.9 hPa	23.6 C deg	1026.6 hPa	14.2 C deg
1776947761	989.1 hPa	24.4 C deg	1028.9 hPa	17.9 C deg
1776945946	989.4 hPa	24 C deg	1029.2 hPa	16.8 C deg
1776935056	991.6 hPa	23.3 C deg	1031.6 hPa	14.4 C deg
1776933241	992.1 hPa	23.4 C deg	1032.1 hPa	13.6 C deg
1776847933	990.8 hPa	22.7 C deg	1030.8 hPa	12.7 C deg
1776817085	989.4 hPa	22.3 C deg	1029.5 hPa	2.1 C deg
1776815263	989.5 hPa	22 C deg	1029.6 hPa	2.8 C deg
1776802557	988.7 hPa	22.3 C deg	1028.6 hPa	6.4 C deg
1776798933	988.6 hPa	21.2 C deg	1028.8 hPa	6.7 C deg
1776777147	986.6 hPa	23.3 C deg	1026.3 hPa	10.3 C deg
1776773517	986.4 hPa	24.4 C deg	1026 hPa	13.2 C deg
1776760811	985.8 hPa	23.5 C deg	1025.5 hPa	12.9 C deg
1776671874	984.1 hPa	23.7 C deg	1023.7 hPa	12.2 C deg
1776660984	984.5 hPa	22 C deg	1024.4 hPa	5.1 C deg
1776641019	985.8 hPa	22.2 C deg	1025.6 hPa	7.3 C deg
1776327017	989.7 hPa	23.5 C deg	1029.6 hPa	16.9 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)