F4IQP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4IQP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1761537957	12.53 Volt	0 Pkt	100 Pcnt
1761533937	12.53 Volt	0 Pkt	100 Pcnt
1761529917	12.53 Volt	0 Pkt	100 Pcnt
1761525904	12.53 Volt	0 Pkt	100 Pcnt
1761521879	12.53 Volt	0 Pkt	100 Pcnt
1761517857	12.53 Volt	0 Pkt	100 Pcnt
1761513837	12.53 Volt	0 Pkt	100 Pcnt
1761509818	12.53 Volt	0 Pkt	100 Pcnt
1761509398	12.53 Volt	0 Pkt	100 Pcnt
1761504158	12.53 Volt	0 Pkt	100 Pcnt
1761500138	12.53 Volt	0 Pkt	100 Pcnt
1761496118	12.53 Volt	0 Pkt	100 Pcnt
1761492098	12.53 Volt	0 Pkt	90 Pcnt
1761488078	12.53 Volt	0 Pkt	100 Pcnt
1761487658	12.53 Volt	0 Pkt	100 Pcnt
1761467016	12.45 Volt	0 Pkt	20 Pcnt
1761462996	12.53 Volt	10 Pkt	37 Pcnt
1761462697	12.53 Volt	10 Pkt	44 Pcnt
1761459037	12.53 Volt	0 Pkt	18 Pcnt
1761458976	12.53 Volt	0 Pkt	18 Pcnt
1761455377	12.53 Volt	0 Pkt	24 Pcnt
1761450936	12.53 Volt	10 Pkt	57 Pcnt
1761448057	12.53 Volt	20 Pkt	82 Pcnt
1761446916	12.53 Volt	20 Pkt	70 Pcnt
1761444397	12.53 Volt	20 Pkt	80 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)