DB0LP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0LP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1757453288	12.53 Volt	340 Pkt	120 Pkt	71 Pcnt
1757452688	12.53 Volt	330 Pkt	120 Pkt	68 Pcnt
1757452088	12.53 Volt	320 Pkt	130 Pkt	68 Pcnt
1757451488	12.53 Volt	310 Pkt	120 Pkt	67 Pcnt
1757450888	12.53 Volt	310 Pkt	130 Pkt	66 Pcnt
1757450288	12.53 Volt	300 Pkt	130 Pkt	67 Pcnt
1757449698	12.53 Volt	310 Pkt	130 Pkt	68 Pcnt
1757449088	12.53 Volt	300 Pkt	130 Pkt	68 Pcnt
1757448488	12.53 Volt	290 Pkt	120 Pkt	69 Pcnt
1757447888	12.53 Volt	290 Pkt	110 Pkt	69 Pcnt
1757447288	12.53 Volt	260 Pkt	100 Pkt	68 Pcnt
1757446688	12.53 Volt	270 Pkt	110 Pkt	68 Pcnt
1757446089	12.53 Volt	240 Pkt	90 Pkt	68 Pcnt
1757445488	12.53 Volt	250 Pkt	100 Pkt	70 Pcnt
1757444889	12.53 Volt	260 Pkt	100 Pkt	71 Pcnt
1757444288	12.53 Volt	260 Pkt	100 Pkt	69 Pcnt
1757443688	12.53 Volt	280 Pkt	110 Pkt	70 Pcnt
1757443089	12.53 Volt	280 Pkt	110 Pkt	67 Pcnt
1757442488	12.53 Volt	310 Pkt	130 Pkt	68 Pcnt
1757441889	12.53 Volt	340 Pkt	130 Pkt	67 Pcnt
1757441289	12.53 Volt	350 Pkt	140 Pkt	65 Pcnt
1757440689	12.53 Volt	340 Pkt	140 Pkt	64 Pcnt
1757440089	12.53 Volt	360 Pkt	160 Pkt	63 Pcnt
1757439489	12.53 Volt	350 Pkt	160 Pkt	62 Pcnt
1757438889	12.53 Volt	300 Pkt	130 Pkt	60 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)