This is the latest recevied telemetry packets stored in our database for station/object DO1HOZ-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1757632891
960.8 hPa
25 C deg
49.5 %
1014.2 hPa
0 C deg
1757631091
960.9 hPa
25.1 C deg
49.5 %
1014.3 hPa
0 C deg
1757629291
961 hPa
25.2 C deg
49.5 %
1014.3 hPa
0 C deg
1757627490
960.8 hPa
25.2 C deg
49.5 %
1014.1 hPa
0 C deg
1757625690
960.8 hPa
25.3 C deg
49.5 %
1014.2 hPa
0 C deg
1757623890
960.8 hPa
25.6 C deg
49.1 %
1014 hPa
0 C deg
1757622090
960.7 hPa
25.6 C deg
48.9 %
1014 hPa
0 C deg
1757620297
960.7 hPa
25.7 C deg
48.2 %
1013.9 hPa
0 C deg
1757619039
960.7 hPa
26.2 C deg
47.3 %
1013.8 hPa
0 C deg
1757617249
960.5 hPa
27 C deg
47.1 %
1013.4 hPa
0 C deg
1757447851
959.8 hPa
27.1 C deg
46.1 %
1012.8 hPa
0 C deg
1757447180
959.7 hPa
26.6 C deg
46.9 %
1014.7 hPa
0 C deg
1757447031
959.6 hPa
27.7 C deg
45.1 %
1014.4 hPa
0 C deg
1757445961
959.6 hPa
26.4 C deg
47.7 %
1014.7 hPa
0 C deg
1757365469
960.2 hPa
27 C deg
45.1 %
1015.2 hPa
0 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)