CR7BQX-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CR7BQX-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TX*	RX*	V_Bat*	V_Ext*
1757564040	36 Count	329 Count	4.24 VDC	0.14 VDC
1757562237	35 Count	311 Count	4.22 VDC	0.14 VDC
1757560434	34 Count	292 Count	4.26 VDC	0.14 VDC
1757558631	33 Count	273 Count	4.22 VDC	0.14 VDC
1757556829	32 Count	246 Count	4.23 VDC	0.14 VDC
1757555075	27 Count	225 Count	4.28 VDC	0.14 VDC
1757553272	26 Count	206 Count	4.27 VDC	0.14 VDC
1757551469	25 Count	188 Count	4.24 VDC	0.14 VDC
1757549666	24 Count	169 Count	4.22 VDC	0.14 VDC
1757547863	23 Count	150 Count	4.2 VDC	0.14 VDC
1757546061	22 Count	131 Count	4.21 VDC	0.14 VDC
1757544258	21 Count	112 Count	4.26 VDC	0.14 VDC
1757542455	20 Count	95 Count	4.2 VDC	0.14 VDC
1757540652	19 Count	77 Count	4.23 VDC	0.14 VDC
1757538857	18 Count	58 Count	4.24 VDC	0.14 VDC
1757537047	17 Count	41 Count	4.26 VDC	0.14 VDC
1757535244	16 Count	12 Count	4.2 VDC	0.14 VDC
1757535225	14 Count	12 Count	4.22 VDC	0.14 VDC
1757535159	10 Count	10 Count	4.26 VDC	0.14 VDC
1757535150	8 Count	10 Count	4.25 VDC	0.14 VDC
1757534766	3 Count	2 Count	4.26 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)