This is the latest recevied telemetry packets stored in our database for station/object DG0OPK-33. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1757640371
960.2 hPa
31.3 C deg
0 %
1015.7 hPa
0 C deg
1757638571
960.2 hPa
31.3 C deg
0 %
1015.7 hPa
0 C deg
1757636771
960 hPa
31.3 C deg
0 %
1015.5 hPa
0 C deg
1757634971
960.2 hPa
31.3 C deg
0 %
1015.7 hPa
0 C deg
1757633171
960.3 hPa
31.2 C deg
0 %
1015.8 hPa
0 C deg
1757631371
960.3 hPa
31.3 C deg
0 %
1015.8 hPa
0 C deg
1757629570
960.3 hPa
31.4 C deg
0 %
1015.8 hPa
0 C deg
1757627777
960.1 hPa
31.6 C deg
0 %
1015.5 hPa
0 C deg
1757625977
960.1 hPa
31.3 C deg
0 %
1015.6 hPa
0 C deg
1757625409
960.1 hPa
31.1 C deg
0 %
1015.7 hPa
0 C deg
1757623609
960 hPa
31 C deg
0 %
1015.6 hPa
0 C deg
1757621803
959.9 hPa
31.3 C deg
0 %
1015.4 hPa
0 C deg
1757621581
959.9 hPa
31.4 C deg
0 %
1015.3 hPa
0 C deg
1757619974
959.8 hPa
31.6 C deg
0 %
1015.2 hPa
0 C deg
1757619866
959.7 hPa
31.6 C deg
0 %
1015.2 hPa
0 C deg
1757619837
959.8 hPa
31.6 C deg
0 %
1015.2 hPa
0 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)