DG2MCM-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG2MCM-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	SkyT*	AOD*	CCT*
1773202749	3 °C	2.55 x100	0 K/100
1773202135	3 °C	2.55 x100	0 K/100
1773201521	3 °C	2.55 x100	0 K/100
1773200293	4 °C	2.55 x100	0 K/100
1773199065	4 °C	2.55 x100	0 K/100
1773198451	4 °C	2.55 x100	0 K/100
1773197837	-7 °C	2.55 x100	0 K/100
1773197223	4 °C	2.55 x100	0 K/100
1773196610	3 °C	2.55 x100	0 K/100
1773195996	4 °C	2.55 x100	0 K/100
1773194767	4 °C	2.55 x100	0 K/100
1773194153	3 °C	2.55 x100	0 K/100
1773193539	0 °C	2.55 x100	1300 K/100
1773191697	2 °C	2.55 x100	0 K/100
1773191083	2 °C	2.55 x100	0 K/100
1773186785	2 °C	2.55 x100	0 K/100
1773186171	2 °C	2.55 x100	0 K/100
1773185557	2 °C	2.55 x100	0 K/100
1773183715	4 °C	2.55 x100	0 K/100
1773183101	2 °C	2.55 x100	0 K/100
1773181873	-6 °C	2.55 x100	0 K/100
1773181259	-4 °C	2.55 x100	0 K/100
1773180031	-1 °C	2.55 x100	0 K/100
1773179417	0 °C	2.55 x100	0 K/100
1773178189	1 °C	2.55 x100	0 K/100

*Used Equation Coefficients:

SkyT: 0, 1, -50

Lux: 0, 100, 0

AOD: 0, 0.01, 0

RGBr: 0, 0.01, 0

CCT: 0, 100, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)