This is the latest recevied telemetry packets stored in our database for station/object BV8SI-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
CPUTemp*
RxPkts/20m*
RxPkts/1h*
RxPkts/24h*
DiGi*
1753781785
0.12 Rx Erlang
0.07 Tx Erlang
39 count/10m
1027 count/10m
0 count/10m
1753781013
1 Rx Erlang
0 Tx Erlang
4 count/10m
0 count/10m
0 count/10m
1753780585
23.9 Rx Erlang
14 Tx Erlang
35 count/10m
1026 count/10m
0 count/10m
1753779813
0.9 Rx Erlang
0 Tx Erlang
3 count/10m
0 count/10m
0 count/10m
1753779384
22.5 Rx Erlang
12 Tx Erlang
34 count/10m
1022 count/10m
0 count/10m
1753778613
0.7 Rx Erlang
0 Tx Erlang
3 count/10m
0 count/10m
0 count/10m
1753778185
22.4 Rx Erlang
9 Tx Erlang
34 count/10m
1022 count/10m
0 count/10m
1753777413
1.1 Rx Erlang
0 Tx Erlang
4 count/10m
0 count/10m
0 count/10m
1753776213
0.7 Rx Erlang
0 Tx Erlang
4 count/10m
0 count/10m
0 count/10m
1753775785
23.9 Rx Erlang
12 Tx Erlang
34 count/10m
1028 count/10m
0 count/10m
1753775013
0.8 Rx Erlang
0 Tx Erlang
3 count/10m
0 count/10m
0 count/10m
1753774584
23 Rx Erlang
9 Tx Erlang
41 count/10m
1028 count/10m
0 count/10m
*Used Equation Coefficients:
CPUTemp: 0, 0.005, 0
RxPkts/20m: 0, 0.005, 0
RxPkts/1h: 0, 1, 0
RxPkts/24h: 0, 1, 0
DiGi: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)