OE3XWJ-92 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XWJ-92. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	60 Wasserstand*	65 Wassertemperatur*	50 Batteriespannung*
1781594757	15.1 cm	24 °C	13.2 V
1781594450	15 cm	24.1 °C	13.2 V
1781593860	15.1 cm	24.3 °C	13.2 V
1781593558	15.1 cm	24.3 °C	13.2 V
1781593265	15.1 cm	24.4 °C	13.2 V
1781592373	15.1 cm	24.6 °C	13.2 V
1781591440	15.1 cm	24.7 °C	13.2 V
1781590861	15 cm	24.8 °C	13.2 V
1781590548	15 cm	24.8 °C	13.2 V
1781589046	15 cm	24.8 °C	13.3 V
1781515856	15 cm	24.5 °C	13.2 V
1781514122	15.1 cm	24.5 °C	13.2 V
1781513466	15 cm	24.5 °C	13.2 V
1781513154	15 cm	24.5 °C	13.2 V
1781511659	15 cm	24.5 °C	13.2 V
1781501760	15.1 cm	24.6 °C	13.2 V
1781167562	14.8 cm	23.4 °C	13.2 V
1781166660	14.8 cm	23.4 °C	13.2 V
1781072749	14.8 cm	24.2 °C	13.2 V
1781072452	14.9 cm	24.3 °C	13.2 V
1781071257	14.9 cm	24.3 °C	13.2 V
1781010639	14.8 cm	24.4 °C	13.2 V
1780991448	14.8 cm	23.9 °C	13.2 V
1780990553	14.8 cm	23.9 °C	13.2 V
1780990257	14.8 cm	23.9 °C	13.2 V

*Used Equation Coefficients:

60 Wasserstand: 0, 1, 0

65 Wassertemperatur: 0, 1, 0

50 Batteriespannung: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)