W6UA-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6UA-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1776655267	12.68 Volt	2 Pcnt	19 C
1776654367	12.68 Volt	2 Pcnt	19.5 C
1776654366	12.68 Volt	2 Pcnt	19.5 C
1776653467	12.68 Volt	2 Pcnt	20 C
1776652567	12.68 Volt	2 Pcnt	21 C
1776652566	12.68 Volt	2 Pcnt	21 C
1776651667	12.68 Volt	2 Pcnt	22 C
1776650767	12.6 Volt	2 Pcnt	23 C
1776650766	12.6 Volt	2 Pcnt	23 C
1776649867	12.68 Volt	2 Pcnt	24 C
1776648967	12.68 Volt	2 Pcnt	25.5 C
1776648966	12.68 Volt	2 Pcnt	25.5 C
1776648067	12.6 Volt	2 Pcnt	27.5 C
1776647167	12.6 Volt	2 Pcnt	28.5 C
1776647166	12.6 Volt	2 Pcnt	28.5 C
1776646267	12.68 Volt	2 Pcnt	29 C
1776645367	12.6 Volt	2 Pcnt	28.5 C
1776645366	12.6 Volt	2 Pcnt	28.5 C
1776644467	12.68 Volt	2 Pcnt	27.5 C
1776643567	12.6 Volt	2 Pcnt	27 C
1776643566	12.6 Volt	2 Pcnt	27 C
1776642667	12.68 Volt	2 Pcnt	26.5 C
1776641767	12.68 Volt	2 Pcnt	26 C
1776641766	12.68 Volt	2 Pcnt	26 C
1776640867	12.68 Volt	2 Pcnt	26 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)